Yamaha YZFR1W 2007 Скачать руководство пользователя страница 356 | Manualshive

Страница: 356 / 429

background image

FUEL INJECTION SYSTEM

8-37

NOTE:

If the engine stop switch is set to “

”, set it to “

”, and then set it to “

” again.

9. Turn the main switch to “OFF” to cancel the diagnostic mode.

Fault code table

Fault
code

No.

Symptom

Probable cause of malfunction

Diagnostic

code No.

11

No normal signals are
received from the cylinder
identification sensor when
the engine is started or
while the vehicle is being
driven.

• Open or short circuit in sub-wire-harness 1.
• Open or short circuit in wire harness.
• Defective cylinder identification sensor.
• Malfunction in ECU.
• Improperly installed sensor.

—

12

No normal signals are
received from the crank-
shaft position sensor.

• Open or short circuit in wire harness.
• Defective crankshaft position sensor.
• Malfunction in pickup rotor.
• Malfunction in ECU.
• Improperly installed sensor.

—

13

Intake air pressure sensor:
open or short circuit
detected.

• Open or short circuit in wire harness.
• Defective intake air pressure sensor.
• Malfunction in ECU.

03

14

Intake air pressure sensor:
hose system malfunction
(clogged or detached
hose).

• Intake air pressure sensor hose is

detached, clogged, kinked, or pinched.

• Malfunction in ECU.

03

15

Throttle position sensor (for
throttle valves): open or
short circuit detected.
Throttle position sensor (for
throttle valves) coupler con-
nection is loose.

• Open or short circuit in wire harness.
• Defective throttle position sensor (for throt-

tle valves).

• Malfunction in ECU.
• Improperly installed throttle position sensor

(for throttle valves).

01
13

17

EXUP servo motor circuit:
open or short circuit
detected or loose connec-
tion.

• Open or short circuit in wire harness.
• Defective EXUP servo motor (potentiometer

circuit).

53

18

EXUP servo motor is stuck.

• Open or short circuit in wire harness.
• Stuck EXUP servo motor (mechanism).
• Stuck EXUP servo motor (motor).

53

19

Open circuit is detected in
the input lead from the side-
stand switch to the ECU.

• Open circuit in wire harness (ECU Coupler).
• Malfunction in ECU.
• Relay unit (diode)

20

«
...
354
355
356
357
358
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

SIDE FORCE 445cc

Бренд: Mash Страницы: 27

Бренд: yasuni Страницы: 8

Бренд: HYOSUNG Страницы: 199

Бренд: hepco & becker Страницы: 6

Бренд: Honda Страницы: 186

D14/4 BANTAM SUPREME D14/4 BANTAM SPORTS

Бренд: BSA Страницы: 120

Бренд: KTM Power Parts Страницы: 22

Easyrack 6612533 01 01

Бренд: hepco & becker Страницы: 5

Бренд: Androware Страницы: 2

Бренд: KC Страницы: 32

Бренд: DYNATEK Страницы: 7

Бренд: DYNATEK Страницы: 12

Бренд: Arai Страницы: 15

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 278

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды