Yamaha YZFR1W 2007 Скачать руководство пользователя страница 392 | Manualshive

Страница: 392 / 429

background image

IMMOBILIZER SYSTEM

8-73

Standard key registration:

Standard key registration is required when a standard key is lost and needs to be replaced, or when
the code re-registering key is re-registered after the immobilizer unit or ECU are replaced.

NOTE:

Do not start the engine with a standard key that has not been registered. If the main switch is turned
“ON” with a standard key that has not been registered, the immobilizer system indicator light flashes
to indicate fault code “52”. (Refer to "SELF-DIAGNOSIS FAULT CODE INDICATION" on page 8-75).

1. Check that the immobilizer system indicator light signals the standby mode.
2. Using the code re-registering key, turn the main switch to “ON”, then “OFF”, and then remove the

key within 5 seconds.

3. Insert the first standard key to be registered into the main switch, then turn the key to “ON” within

5 seconds to activate the key registration mode.

NOTE:

The existing standard key code is erased from the memory when the key registration mode is acti-
vated. When the key registration mode is activated, the immobilizer system indicator light flashes
rapidly.

4. While the indicator light is flashing, turn the main switch to “OFF”, remove the key, and within 5

seconds, insert the second standard key to be registered into the main switch.

NOTE:

If he immobilizer system indicator light stops flashing 5 seconds after the first standard key is regis-
tered, the registration mode is deactivated. If this occurs, the second standard key cannot be regis-
tered, and steps 2 to 4 need to be repeated to register both standard keys.

5. Turn the main switch to “ON”.

NOTE:

When the indicator light goes off, the registration is complete.

6. Check that the engine can be started with the two registered standard keys.

Standard key registration

e. Standby mode on
f. Standby mode off

a. Main switch “ON”
b. Main switch “OFF”
c. LED on
d. LED off
e. Less than 5.0 s
f. Code re-registering key
g. First standard key
h. Second standard key
i. Registration mode

A. Registration of the second standard key is

complete.

B. Immobilizer system indicator light stops

flashing when the registration of the second
standard key is complete.

«
...
390
391
392
393
394
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: hepco & becker Страницы: 4

Power Commander III 718-411

Бренд: Dynojet Страницы: 3

Бренд: AMFD Страницы: 17

Pulsar 135 BS VI

Бренд: Bajaj Страницы: 48

Бренд: KTM Power Parts Страницы: 12

Бренд: Bajaj Страницы: 319

LEDV46-T-TS LIGHT KIT

Бренд: AdMore Lighting Страницы: 4

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 8

Бренд: R&G Страницы: 17

Бренд: R&G Страницы: 15

Бренд: R&G Страницы: 21

Бренд: VOR Motori Страницы: 100

Kawasaki NINJA 650

Бренд: Arrow Страницы: 7

Бренд: Beta Страницы: 20

Бренд: APRILIA Страницы: 88

Бренд: Electronicbox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды