Yamaha YZFR1W 2007 Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 429

background image

CHAIN DRIVE

4-72

EAS23410

REMOVING THE DRIVE CHAIN

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the rear wheel is elevated.

2. Remove:

• Drive chain

(with the drive chain cutter)

EAS23440

CHECKING THE DRIVE CHAIN

1. Measure:

• Measure the dimension between 15-links

on the inner side “a” and outer side “b” of
the roller and calculate the dimension
between pin centers.

• Dimension “c” between pin centers = (Inner

dimension “a” + Outer dimension “b”)/2

• 15-link section “c” of the drive chain

Out of specification

→

Replace the drive

chain, front drive sprocket and rear drive
sprocket as a set.

NOTE:

• While measuring the 15-link section, push

down on the drive chain to increase its ten-
sion.

• Perform this measurement at two or three dif-

ferent places.

2. Check:

• Drive chain

Stiffness

→

Clean and lubricate or replace.

3. Clean:

• Drive chain

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Wipe the drive chain with a clean cloth.
b. Put the drive chain in kerosene and remove

any remaining dirt.

c. Remove the drive chain from the kerosene

and completely dry it.

CAUTION:

ECA4C81003

• This vehicle has a drive chain with small

rubber O-rings “1” between the drive
chain side plates. Never use high-pres-
sure water or air, steam, gasoline, certain
solvents (e.g., benzine), or a coarse brush
to clean the drive chain. High-pressure
methods could force dirt or water into the
drive chain’s internals, and solvents will
deteriorate the O-rings. A coarse brush
can also damage the O-rings. Therefore,
use only kerosene to clean the drive
chain.

• Do not soak the drive chain in kerosene

for more than ten minutes, otherwise the
O-rings can be damaged.

15-link length limit

239.3 mm (9.42 in)

«
...
192
193
194
195
196
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Quantum hardcoated N30214-WK

Бренд: National Cycle Страницы: 13

SUPERSPORT1000 2003

Бренд: Ducati Страницы: 328

Бренд: DYNATEK Страницы: 8

2004 Moto Matrix

Бренд: Yamaha Страницы: 41

Бренд: Yamaha Страницы: 48

Бренд: Yamaha Страницы: 28

2004 FJR1300(S)

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 30

Бренд: Yamaha Страницы: 87

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 106

2005 V Star XVS1100T

Бренд: Yamaha Страницы: 82

2005 Virago XV250T

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 94

2005 Royal Star XVZ13CTT

Бренд: Yamaha Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды