Yamaha YZFR1W 2007 Скачать руководство пользователя страница 308 | Manualshive

Страница: 308 / 429

background image

FUEL TANK

7-2

EAS26630

REMOVING THE FUEL TANK

1. Extract the fuel in the fuel tank through the

fuel tank cap with a pump.

2. Remove:

• Fuel hose connector cover
• Fuel hose
• Fuel sender coupler
• Fuel pump coupler
• Fuel tank drain hose
• Fuel tank breather hose
• Fuel tank side cover

CAUTION:

ECA4C81002

• Be sure to disconnect the fuel hose by

hand. Do not forcefully disconnect the
hose with tools.

• Although the fuel has been removed from

the fuel tank be careful when removing
the fuel hoses, since there may be fuel
remaining in it.

NOTE:

• To remove the fuel hose from the fuel injec-

tion pipe, slide the cover “a” on the end of the
hose in the direction of the arrow shown and
then remove the hose.

• Before removing the hoses, place a few rags

in the area under where it will be removed.

3. Remove:

• Fuel tank

NOTE:

Do not set the fuel tank down so that the instal-
lation surface of the fuel pump is directly under
the tank. Be sure to lean the fuel tank in an
upright position.

EAS26640

REMOVING THE FUEL PUMP

1. Remove:

• Fuel pump

CAUTION:

ECA14720

• Do not drop the fuel pump or give it a

strong shock.

• Do not touch the base section of the fuel

sender.

EAS26670

CHECKING THE FUEL PUMP BODY

1. Check:

• Fuel pump body

Obstruction

→

Clean.

Cracks/damage

→

Replace the fuel pump

assembly.

2. Check:

• Diaphragms and gaskets

Turn/fatigue/cracks

→

Replace the fuel

pump assembly.

EAS26690

CHECKING THE FUEL PUMP OPERATION

1. Check:

• Fuel pump operation

Refer to "CHECKING THE FUEL PRES-
SURE" on page 7-6.

EAS26710

INSTALLING THE FUEL PUMP

1. Install:

• Fuel pump

NOTE:

• Do not damage the installation surface of the

fuel tank when installing the fuel pump.

• Always use a new fuel pump gasket.
• Install the fuel pump as shown in the illustra-

tion.

• Align the projection “a” on the fuel pump with

the slot in the fuel pump bracket.

• Tighten the fuel pump bolts in stages in a

crisscross pattern and to the specified
torque.

Fuel pump bolt

4 Nm (0.4 m·kg, 2.9 ft·lb)

«
...
306
307
308
309
310
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: Kask Страницы: 68

Scout 25L Pannier Kit V2.0

Бренд: MOSKO MOTO Страницы: 13

Бренд: X-lite Страницы: 33

RACE 11621C0520

Бренд: Yoshimura Страницы: 7

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 84

NMAX GPD155 2020

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 104

NEO'S ESS025 2022

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды