Yamaha YZFR1W 2007 Скачать руководство пользователя страница 377

Страница: 377 / 429

FUEL INJECTION SYSTEM

8-58

Fault code No.

Symptom

ANo normal signals are received from the speed sensor.
BOpen circuit is detected in the neutral switch.

Diagnostic code No.

Speed sensor

Neutral switch

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

A-1

Installed state of speed sensor.

Check for looseness or pinching.

Starting the
engine, and
activating the
speed sensor
by operating the
vehicle.

A-2

Connections
• Speed sensor coupler
• Main wire harness ECU coupler

• Check the couplers for any pins

that may be pulled out.

• Check the locking condition of

the couplers.

• If there is a malfunction, repair it

and connect the coupler
securely.

A-3

Open or short circuit in lead.

• Repair or replace if there is an

open or short circuit.

• Between speed sensor coupler

and ECU coupler.
(Blue–Blue)
(White/Yellow–White/Yellow)
(Black/Blue–Black/Blue)

A-4

Defective speed sensor.

• Execute the diagnostic mode.

(Code No. 07)

• Replace if defective.

Refer to "CHECKING THE
SPEED SENSOR" on page 8-
95.

B-1

Installed state of neutral switch.

Check for looseness or pinching.

B-2

Connections
• Neutral switch coupler
• Main wire harness ECU coupler

• Check the couplers for any pins

that may be pulled out.

• Check the locking condition of

the couplers.

• If there is a malfunction, repair it

and connect the coupler
securely.

B-3

Open circuit in neutral switch lead.

• Repair or replace if there is an

open circuit.

• Between neutral switch coupler

and relay unit coupler.
(Sky blue–Sky blue)

• Between relay unit coupler and

ECU coupler.
(Blue/Yellow–Blue/Yellow)

B-4

Defective neutral switch.

• Execute the diagnostic mode.

(Code No.21)

• Replace if defective.

Refer to "CHECKING THE
SWITCHES" on page 8-81.

B-5

Faulty shift drum (neutral detection
area).

• Replace if defective.

Refer to "TRANSMISSION" on
page 5-84.

Содержание YZFR1W 2007














































































































































































































































































































































































































































Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды

Yamaha YZFR1W 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды