Yamaha YZFR1W 2007 Скачать руководство пользователя страница 376

Страница: 376 / 429

FUEL INJECTION SYSTEM

8-57

Fault code No.

Symptom Lean angle sensor: open or short circuit detected.

Diagnostic code No.

Lean angle sensor

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

Connections
• Lean angle sensor coupler
• Main wire harness ECU coupler

• Check the coupler for any pins

that may be pulled out.

• Check the locking condition of

the coupler.

• If there is a malfunction, repair it

and connect the coupler
securely.

Reinstated
automatically if
a normal signal
is received.

Open or short circuit in lead wire.

• Repair or replace if there is an

open or short circuit.

• Between lean angle sensor

coupler and ECU coupler.
(Blue–Blue)
(Yellow/Green–Yellow/Green)
(Black/Blue–Black/Blue)

Defective lean angle sensor.

• Execute the diagnostic mode.

(Code No.08)

• Replace if defective.

Refer to "CHECKING THE
LEAN ANGLE SENSOR" on
page 8-92.

Содержание YZFR1W 2007














































































































































































































































































































































































































































Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды

Yamaha YZFR1W 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды