Yamaha YZFR1W 2007 Скачать руководство пользователя страница 403 | Manualshive

Страница: 403 / 429

background image

ELECTRICAL COMPONENTS

8-84

EAS27990

CHECKING THE BULBS AND BULB SOCK-
ETS

Check each bulb and bulb socket for damage
or wear, proper connections, and also for conti-
nuity between the terminals.
Damage/wear

→

Repair or replace the bulb,

bulb socket or both.
Improperly connected

→

Properly connect.

No continuity

→

Repair or replace the bulb,

bulb socket or both.

Types of bulbs

The bulbs used on this vehicle are shown in
the illustration.
• Bulbs “a” are used for the headlights and

usually use a bulb holder that must be
detached before removing the bulb.

• Bulbs “b” is used for turn signal and can be

removed from the socket by pushing and
turning the bulb counterclockwise.

• Bulbs “c” are used for auxiliary lights and can

be removed from their respective socket by
carefully pulling them out.

Checking the condition of the bulbs

The following procedure applies to all of the
bulbs.
1. Remove:

• Bulb

WARNING

EWA13320

Since the headlight bulb gets extremely
hot, keep flammable products and your
hands away from the bulb until it has
cooled down.

CAUTION:

ECA14380

• Be sure to hold the socket firmly when

removing the bulb. Never pull the lead,
otherwise it may be pulled out of the ter-
minal in the coupler.

• Avoid touching the glass part of the head-

light bulb to keep it free from oil, other-

wise the transparency of the glass, the
life of the bulb, and the luminous flux will
be adversely affected. If the headlight
bulb gets soiled, thoroughly it with a cloth
moistened with alcohol or lacquer thin-
ner.

2. Check:

• Bulb (for continuity)

(with the pocket tester)
No continuity

→

Replace.

NOTE:

Before checking for continuity, set the pocket
tester to “0” and to the “

Ω

×

1” range.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the positive tester probe to termi-

nal “1” and the negative tester probe to ter-
minal “2”, and check the continuity.

b. Connect the positive tester probe to termi-

nal “1” and the negative tester probe to ter-
minal “3” and check the continuity.

c. If either of the readings indicate no continu-

ity, replace the bulb.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Checking the condition of the bulb sockets

The following procedure applies to all of the
bulb sockets.
1. Check:

• Bulb socket (for continuity)

(with the pocket tester)
No continuity

→

Replace.

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

«
...
401
402
403
404
405
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: hepco & becker Страницы: 4

Freeride 350 AUS

Бренд: KTM Страницы: 25

Бренд: Crivit Страницы: 58

BLITZ 9-13 Visor

Бренд: Fubag Страницы: 17

Can-Am Spyder RT

Бренд: F4Customs Страницы: 3

Бренд: RIEJU Страницы: 280

Бренд: Vetter Страницы: 11

Krauser 610.092 00 02

Бренд: Wunderlich Страницы: 4

MADISON 3 125 cc

Бренд: Malaguti Страницы: 38

XSM POWER UP 2007

Бренд: Malaguti Страницы: 53

Бренд: Baotian Страницы: 22

Бренд: APRILIA Страницы: 197

YFM660RP 5LP2-AE2 2002

Бренд: Yamaha Страницы: 33

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 100

YP250 5GM2-AE1 2000

Бренд: Yamaha Страницы: 105

Бренд: Yamaha Страницы: 146

Бренд: Yamaha Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды