Yamaha YZFR1W 2007 Скачать руководство пользователя страница 415

Страница: 415 / 429

ELECTRICAL COMPONENTS

8-96

b. Set the main switch to “ON”.
c. Elevate the rear wheel and slowly rotate it.
d. Measure the voltage (DC 5 V) of White/Yel-

low and Black/Blue. With each full rotation
of the rear wheel, the voltage reading
should cycle from 0.6 V 4.8V to 0.6 V to 4.8
V.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS4C81021

CHECKING THE RADIATOR FAN MOTORS

1. Check:

• Radiator fan motor

Faulty/rough movement

→

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Disconnect the radiator fan motor coupler

from the wire harness.

b. Connect the battery (DC 12 V) as shown.

c. Measure the radiator fan motor movement.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS28260

CHECKING THE COOLANT TEMPERATURE
SENSOR

1. Remove:

• Coolant temperature sensor

WARNING

EWA14130

• Handle the coolant temperature sensor

with special care.

• Never subject the coolant temperature

sensor to strong shocks. If the coolant
temperature sensor is dropped, replace it.

2. Check:

• Coolant temperature sensor resistance

Out of specification

→

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (

Ω

100) to the

coolant temperature sensor “1” as shown.

b. Immerse the coolant temperature sensor in

a container filled with coolant “2”.

NOTE:

Make sure the coolant temperature sensor ter-
minals do not get wet.

c. Place a thermometer “3” in the coolant.

• Positive tester probe

Blue “1”

• Negative tester probe

Black “2”

Coolant temperature sensor
resistance

C (32

F): 5.21–6.37 k

Ω

C (176

F): 0.29–0.35 k

Ω

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

Coolant temperature sensor terminal

• Negative tester probe

Coolant temperature sensor terminal

Содержание YZFR1W 2007














































































































































































































































































































































































































































Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды

Yamaha YZFR1W 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды