Thank you for purchasing a Sealey Power Product. Manufactured to a high standard this product will,
if used according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
WELDING HELMET SOLAR POWERED SHADE 9-13
MODEL Nos:
PWH699G, PWH699R, PWH699B
1. SAFETY INSTRUCTIONS
WARNING!
This helmeT is noT suiTable for use wiTh laser or gas welding/CuTTing.
3
Ensure all workshop safety rules, regulations and conditions are complied with when using welding equipment. The helmet
will not offer protection against misuse of workshop tools, equipment, or accessories.
3
Maintain the
helmet in good condition and protect cartridge from liquid and dirt contact. Regularly replace the protective lens
and replace any damaged or worn parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate
the warranty.
3
Whilst the front cover lense is impact resistant it can break in extraordinary circumstances.
Always wear CE approved
safety glasses when using this helmet to provide additional protection against flying particles, splash, spray and
spatter.
3
Ensure the front cover lens is securely in place before use.
3
Fit the helmet and adjust the head band so the helmet will sit as low and near to your face as possible,
3
Use helmet only in temperatures ranging from -10°C to 55°C (14°F to 131°F).
3
Store helmet only in temperatures ranging from -20
°
C to 70°C (-4°F to 158°F).
3
Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery.
3
Maintain correct balance and footing.
3
Ensure the floor is clear from obstructions, not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the working area.
WARNING!
The helmet will only protect the eyes and face from radiation and sparks. It will not protect against explosive
devices or corrosive liquids.
7
DO NOT
use helmet for any other purpose, other than face protection when grinding.
7
DO NOT
use helmet unless you have been instructed in its use by a qualified person.
7
DO NOT
open or tamper with the shade cartridge.
7
DO NOT
get the helmet wet or use in damp or wet locations.
7
DO NOT
leave work place with helmet in lowered position, as bright light source may darken cartridge unexpectedly.
7
DO NOT
place the helmet on a hot surface.
7
DO NOT
use helmet without front cover lens fitted. To do so will invalidate your warranty.
3
Clean helmet (see section 5.4) and store the helmet in a safe, dry, childproof location.
WARNING!
The materials of the helmet may, when coming into contact with the wearers skin, cause an allergic reaction to
susceptible individuals.
WARNING!
Before welding always inspect the cartridge filter to ensure that it is not damaged. To test the filter prior to
welding, direct the front of the cartridge filter to a bright light source which will cause the lens to darken. Then using your
hand rapidly cover and uncover the sensor. The filter should lighten momentarily then return to a dark state.
WARNING! DO NOT use the helmet if damaged or you suspect it may be faulty. (Contact your Sealey dealer).
danger! do noT use if, at any time, the face plate in the cartridge fails to darken
when exposed to a welding spark. remove cartridge and return to your sealey dealer for
inspection. Continued use of the product knowing that the auto darkening feature is
noT funCTioning may damage Your eYes and Cause blindness.
2. INTRODUCTION
High quality lenses with large viewing area
manufactured and tested to BSEN379. Variable
shade from 9-13. Fully automatic switching from light
to dark on striking arc. Fitted with solar power panel -
no batteries required. PWH699 features infinitely
adjustable sensitivity and delay switches. PWH699
Range has a special grinding feature enabling the
user to grind without having to remove the mask, still
offering a full face protection. All models feature
deluxe contoured helmets approved to BSEN175
which give full neck protection and protects lens from
scratching when helmet is laid down. Comfortable
headband and non-slip quick release ratchet
mechanism. Suitable for MIG and arc welding.
Original Language Version
PWH699 Issue No.1 05/11/09
