Vicon RO-C 1400 страница 147 Скачать руководство пользователя

Страница: 147 / 157

Troubleshooting

147

Spreading

tracks visible

among the

crops

Average quality fertiliser. 80% of the

granules with a diameter between 2.0 -

4.75 mm

Determine the distribution and spread

with small working widths if possible

Blend of fertiliser types used. A blend can

become unmixed again or types of

fertiliser could contain varying spreading

qualities.

Check the type, pattern and distribution.

Spread with smaller working widths as far

as possible

52,

New type of fertiliser spread with the

same settings as the previous type.

Quality varies greatly between types.

Determine the characteristics of the

fertiliser, look for the relevant spreading

chart and set the spreader again

Use of wrong spreading chart

Determine the characteristics of the

fertiliser and select the correct spreading

chart

52,

Working with unfavourable weather

conditions: high levels of humidity, rain,

heat or high wind speeds (> 5 m/sec)

Only work under good weather conditions

Incorrect overlapping of the spreading

pattern

Always set the driving tracks before

spreading

101

Horizontal/vertical settings of the machine

not correct

Check if the machine is standing level

horizontally and vertically, unless the

spreading chart indicates otherwise

47,

71,

Spreader not set to the correct height

Check and set to the correct working

height (75 cm above the crops or soil) and

inclination

97,

Working width incorrect

Check the discharge points (left and right)

and the PTO shaft rpm

62,

Worn or missing vanes

Check the vanes

Tyre pressure on the left and right not the

same

Check the tyre pressure

Reduce the spreading disc rpm with the

loss at the safety clutch

Check if the spreading discs are turning

smoothly. Check the safety clutch

132,

The setting mechanism of the discharge

point is not set well

Perform the »Check the setting

mechanism of the discharge point«

137

The dosing mechanism is not set well

Perform the »Check the settings of the

dosing mechanism«

132

Machine

makes a noise

while running

Discharge bushing makes contact with

the spreading disc

Adjust the discharge bushing

132

Spreader put down with filled hopper

Repair the machine. Set the dosing

mechanism and discharge point again

132,

137

Spreading disc hidden/ out of balance

Check the spreading discs for damage

and for the presence of all the vanes

Build-up of fertiliser at the agitator and/or

spreading discs

Remove the fertiliser. Clean the machine

well after each use.

119

Problem

Possible cause

Solution

Pag

Содержание RO-C 1400






























































































































































Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды

Vicon RO-C 1400, Руководство пользователя

Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды