Vicon RO-C 1400 страница 67 Скачать руководство пользователя

Страница: 67 / 157

To be done before spreading

Dosing setting

The dosing setting to be set can be:

•

Read from the relevant spreading chart if a lower application rate

is to be used whereby the fine application kit is used and

Fine

application kit

is indicated under the heading in the spreading

chart:

yes

→

Determine an application rate not given as described in

paragraph »Application rate«from page 63.

•

Calculate using the relevant spreading chart if a lower application

rate is to be used whereby the fine application kit is indeed used

and

Fine application kit

is indicated under the heading in the

spreading chart:

Calculation

As 2 of the 3 dosing openings are closed the flowrate of the remaining

dosing opening should be three times as much in order to obtain an

even application rate.



Read the

Dosing Setting, Discharge Point and kg/min

(flowrate)

from the spreading chart. Calculate the flowrate with the formula

given below.

If the selected application rate or driving speed is not indicated in the

spreading chart the required flowrate can also be calculated as

follows:

Use the letter given for setting the discharge point in the line of the

spreading chart that most closely resembling the calculated flowrate.



Multiply the flowrate (given in the

Kg/min

column or calculated)

with a factor of 3.



Search in the

Kg/min

column for the most comparable flowrate and

read the relevant dosing setting or estimate it as closely as

possible. Do not use the discharge point indicated there!

Setting the spreader



Set the given discharge point as per the prescribed method

→

in paragraph »Discharge point« on page 62.



Set the given or calculated dosing setting as appropriate.

→

see instructions in paragraph »Application rate« from page 63.



Do a calibration test to check the dosing setting,

→

see instructions in paragraph »Calibration test« on page 75.

Field settings

Spreader inclination

0°

PTO revolutions

540

Disc revolutions

731

Fine application kit

Field settings

Spreader inclination

0°

PTO revolutions

540

Disc revolutions

731

Fine application kit

Yes

600

flowrate required (kg/min) =

application rate (kg/ha) x working width (m) x speed (km/h)

Содержание RO-C 1400






























































































































































Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды

Vicon RO-C 1400, Руководство пользователя

Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды