Vicon RO-C 1400 страница 108 Скачать руководство пользователя

Страница: 108 / 157

Use in the field

108

Border spreading

Spreading fertiliser up to the border of the property requires

concentration. On the one hand you want to achieve maximum cover to

the field edge to ensure a good crop, while on the other hand you want

to minimise the loss over the field edge.

The spreader has 2 different functions and accessories to cater for

border spreading.

•

one-sided boundary spreading with the border spreading plate,

•

boundary track spreading with the tramline cylinder.

When one-sided boundary spreading, drive with the tractor along the

field edge and spread from the border inwards. With boundary track

spreading, drive down the first sprayer tramline from the field edge and

spray in the direction of the border.

One-sided boundary

spreading with the

border spreading plate

Operation

Drive along the field edge when one-sided boundary spreading and

send the flow of fertiliser granules with a border spreading plate

(optional extra). The working width on the side of the field edge can be

adjusted by changing the border spreading plate (optional extra).

Application rate correction with

border spreading

It should be possible to adjust the set application rate while busy with

border spreading using the border spreading plate, depending on the

method of fertilization:

Situation A meadow fertilizing with full adjoining working width:

Adjust the application rate as per the chart given here.

→

See also paragraph »Application rate« on page 63.

Situation B Fertilizing along tramlines:

Application rate as set for full field spreading.

75 cm

Situation A

Working width (WB)

Border spreading plate

75 cm

Situation B

Working width (WB)

Direction

(environmental

approach)

Spread less to the field edge. This will decrease

the loss over the field edge, but the cover will

not be as good

Direction

(profit approach)

Spread more to the field edge. Cover is better,

but the loss is greater

WW
(m)

Rpm
PTO

Situation

540

+40%

540

+35%

540

+30%

540

+25%

21*

450*

+15%

Select higher acceleration with 450 rpm in order to maintain the driving speed or adjust the application rate (-15%) when deceler-

ating.

It is therefore not necessary to adjust the application rate when decelerating (+15% -15%=0).

Содержание RO-C 1400






























































































































































Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды

Vicon RO-C 1400, Руководство пользователя

Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды