Vicon RO-C 1400 страница 87 Скачать руководство пользователя

Страница: 87 / 157

To be done before spreading

Testing the spreading

pattern of the border

spreading plate

Always perform a calibration test first and determine the correct

dosing setting before checking the spreading pattern. Changes to the

dosing setting will also have an influence on the spreading pattern!

→

See paragraph »Calibration test« on page 75.

When using the border spreading plate the aim is to obtain maximum

distribution to the border with minimum loss in the ditch.

This is then why the border spreading plate has to be tested. Do not

perform this test next to the ditch, rather mark a line behind which the

fictive ditch will be.

Operation



Switch the tractor off and remove the key from the ignition and

engage the parking brake of the tractor.



Disconnect the right spreading disc by sliding the connector to the

right. Secure the connector with a lock clip.



Close the dosing unit of the right spreading disc by setting the

dosing knob to 0+0.



Attach the border spreading plate. We recommend that the border

spreading plate should be mounted with the triangle on the fixing

plate.

NDICATION

Check that the vanes do not touch the border spreading plate!



Set the spreader in accordance with the spreading chart for the

desired working width and the instructions given in the “One-sided

boundary spreading" Chapter

(height of the spreading disc = 75

cm above the troughs).



Place 1 trough in the middle of the tractor tracks. The centre of the

driving track must be 2 meters from the line behind which the fictive

ditch is located.

Indication

Position the troughs horizontally with a spirit level!

Border spreading plate

2 m (7 ft)

Connector

Содержание RO-C 1400






























































































































































Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды

Vicon RO-C 1400, Руководство пользователя

Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды