Vicon RO-C 1400 страница 47 Скачать руководство пользователя

Страница: 47 / 157

Connecting to the tractor

Connecting the machine

The space between the spreader and the tractor is limited as far as

possible in order to keep the centre of gravity as closely to the tractor

as possible. This promotes stability and the road behaviour of the

tractor. As a result the coupling shaft, hydraulic hoses and electric

plugs must be connected first, followed by the power lift.

Preparation



Move the tractor to the front of the spreader so that the catch hooks

of the power lift are around 200 mm from the spreader (the

maximum distance depends on the reach of the coupling shaft; the

halves must always overlap each other).



Take the pressure off the hydraulic system of the tractor.



Switch the tractor off, remove the key from the ignition and engage

the parking brake of the tractor.



Put the lower links of the tractor level with the machine linkage

pins.



Compensate for any height difference with the lift rod adjustment

of the power lift.



Adjust the stabiliser chains to make lateral movement of the lower

links impossible.



Mount the appropriate ball bearings to the linkage pins and the top.



Secure the linkage pins and top again.

Front power lift

Only connect the machine to the front power lift if:

•

it has sufficient lifting power,

•

it falls within the same fixing category as the machine,

•

the minimum and maximum load of the front and rear weight would

not be exceeded,

•

the tractor has a closed cabin and proper air filters (active carbon

filters).

Lift rod adjustment

Stabiliser chain

Содержание RO-C 1400






























































































































































Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды

Vicon RO-C 1400, Руководство пользователя

Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды