Vicon RO-C 1400 страница 75 Скачать руководство пользователя

Страница: 75 / 157

To be done before spreading

Calibration test

Avoid contact with the fertiliser and other material

You will most likely get into contact with the fertiliser and other material

you may wish to spread while filling, adjusting and testing the

spreader. Wear protective clothing and gloves, read the safety instruc-

tions provided by the supplier and follow their directions. Contact with

these materials could cause physical harm.

Be careful that nothing gets jammed

It is easy for parts to get jammed while adjusting the spreader.

Work carefully:

•

switch the tractor off and remove the key from the ignition,

•

engage the parking brake of the tractor,

•

wait for all machine parts to come to a standstill before you start

with the adjustments,

•

carefully follow the instructions given.

Friction with these materials could cause physical injury.

The test should be performed on your own. Operate the machine
on your own!

Dangerous situations for other people could easily occur when the

machine is turning and the test conducted. Contact with these

materials could cause physical injury.

Protecting the environment

Spreading a too high dose of materials outside of the field edge,

especially on water surface, creates a heavy burden on the

environment. Protect the environment by applying a correct

application rate in a correct working manner.

PTO shaft rotates after disengaging

After switching off the PTO shaft, danger could arise as the machine

will continue running because of inertia. Keep a safe distance to the

machine until the moving parts have come to a complete stop.

Approaching the machine while it is rotating can cause serious or

deadly injuries.

The spreading charts are compiled for good fertiliser and modern

equipment. It may nevertheless be necessary to check the dosing

settings with a calibration test. This is necessary because your

circumstances and fertiliser will always differ from the test situation

used to compile the spreading charts.

Use the correct flow rate from the chart with the calibration test

The calibration test is used to determine the flowrate of a spreading

disc. The expected flow rate in kg/min differs from the flow rate during

full field spreading. During the calibration test the vanes are removed

and a calibration container is attached. The (corrected) calibration

value is provided in the second column.

You should also test the discharge point with a tray test.

→

See paragraph »Check the spreading pattern (tray test)« on page

80.

Icon at top of

column

Содержание RO-C 1400






























































































































































Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды

Vicon RO-C 1400, Руководство пользователя

Результаты поиска

Содержание RO-C 1400

Отзывы:

Похожие инструкции для RO-C 1400

Бренды по названию

Популярные бренды