Vicon RO-C 1400 Скачать руководство пользователя страница 22

Страница: 22 / 157

Safety

Transport

Check the de coupling ropes of the quick coupling

The de coupling ropes must never be tense and must provide

sufficient freedom for movement, even with the power lift in the lowest

position as it could otherwise accidentally disconnect the quick

coupling.

Drive carefully

Moving behaviour, manoeuvrability and braking performance are

influenced by a trailed machine. When taking turns, pay attention to

the extended width/length (turning circle) and/or large mass

(sluggishness) of the machine! Ensure sufficient braking effect and

safe manageability!

Careless driving could lead to serious injury and damage to the

machine

Adjust the driving speed

High driving speeds and uneven surfaces on the road or field can put

considerable strain on the machine and cause the tractor or machine

to be overstrained, which could lead to damage. Always adjust the

driving speed to the conditions of the environment and the terrain!

When driving up and down hills and across slopes, do not make any

sudden turns!

O n the field

Do not leave the driving cabin

Never leave the operator’s seat during operation or transport. The

driver can be in the danger zone of the tractor or the machine and

could not have a proper view of the immediate vicinity. This could lead

to injury to the driver or third parties.

Do not allow the machine to tilt

When driving up and down hills and across slopes, do not make any

sudden turns! Do not drive transverse on a slope with a steep angle.

Tilting can cause serious machine damage.

Blockage of a security device

In case of a blockage or operation of a security device, never work on

the machine without

•

switching off the PTO shaft,

•

switching off the electric control system,

•

releasing the pressure from the hydraulic system,

•

switching off the tractor engine,

•

the key must be removed from the ignition,

•

engage the parking brake of the tractor.

Содержание RO-C 1400






























































































































































Результаты поиска

Содержание RO-C 1400

Отзывы:

Vicon RO-C 1400, Руководство пользователя, Страница: 22 / 157

Результаты поиска

Содержание RO-C 1400

Отзывы: