VESPA GTV 125 Скачать руководство пользователя страница 81

Страница: 81 / 278

Voltage regulator check

With a perfectly charged battery and lights off,

measure voltage at the battery poles with a high

running engine.

The voltage should not exceed 15.2 Volt.

In case higher voltages are detected, replace the

regulator.

In case of voltage values lower than 14 Volt, check

the stator and the corresponding cable harness.

Recharge system voltage check

Connect an ammeter induction clamp to the volt-

age regulator positive terminal, measure the bat-

tery voltage and turning on the vehicles lights with

engine off, wait for the voltage to set at about 12

V. Start the engine and measure the current gen-

erated by the system with lights on and a high

running engine.

In case the generated current value is lower than

10A, repeat the test using a new regulator and/

stator alternatively.

Vespa GTV 125

Electrical system

ELE SYS - 17

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды