VESPA GTV 125 страница 131 Скачать руководство пользователя

Страница: 131 / 278

Inspecting the wrist pin

- Measure the outer diameter of the gudgeon pin.

- Calculate the coupling clearance between pin

and connecting rod end.

- Measure the capacity diameter on the piston.

- Calculate the piston pin coupling clearance.

- Measure the outside diameter of the piston, per-

pendicular to the gudgeon pin axis.

- Carry out the measurement as shown in the fig-

ure.

41.1 mm (from the crown)

- Using a bore meter, measure the inner cylinder

diameter at three different points according to the

directions shown in the figure.

- Check that the head matching surface exhibits no

deformations or wear.

Maximum admissible displacement: 0.05 mm

- Pistons and cylinders are classified into catego-

ries based on their diameter. The coupling is car-

ried out in pairs (A-A, B-B, C-C, D-D).

- The cylinder rectifying operation should be car-

ried out with a surfacing that respects the original

angle.

- The cylinder surface roughness should be 0.9

micron.

- This is indispensable for a good seating of the

sealing rings, which in turn minimises oil consump-

tion and guarantees optimum performance.

- The pistons are oversized due to cylinder rectifi-

cation and are subdivided into three categories

1st, 2nd, 3rd with 0.2-0.4-0.6 mm oversize. They

are also classified into 4 categories A-A, B-B, C-

C, D-D.

N.B.

THE PIN HOUSINGS HAVE 2 LUBRICATION
CHANNELS. FOR THIS REASON MEASURE-
MENT OF THE DIAMETER MUST BE CARRIED
OUT ACCORDING TO THE AXIS OF THE PIS-
TON.

Vespa GTV 125

Engine

ENG - 33

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды