VESPA GTV 125 Скачать руководство пользователя

Страница: 119 / 278

Refitting the hub cover bearings

For the fitting of the hub box bearings the engine

crankcase and the cover must be heated with the

special heat gun.

- The three 15 mm bearings must be fitted using

the appropriate tools.

- The 42-mm side of the adapter must be turned

towards the bearing.

Specific tooling

020150Y

Air heater support

020151Y

Air heater

020376Y

Adaptor handle

020359Y

42x47-mm adaptor

020412Y

15 mm guide

N.B.

TO FIT THE BEARING ON THE COVER, SUPPORT THE COVER WITH THE STUD BOLT SET.

- Refit the driven pulley shaft bearing with a mod-

ular punch as shown in the figure.

N.B.

IF THE BEARING HAS AN ASYMMETRICAL
BALL RETAINER, PLACE IT SO THAT THE
BALLS ARE VISIBLE FROM THE HUB INNER
SIDE.

Specific tooling

020376Y

Adaptor handle

020359Y

42x47-mm adaptor

020363Y

20 mm guide

N.B.

WHEN FITTING THE BEARINGS ON THE ENGINE CRANKCASE, SUPPORT THE CRANKCASE
PREFERABLY ON A SURFACE TO ALLOW THE BEARINGS TO BE DRIVEN VERTICALLY.

- Refit the seeger ring with the opening facing the bearing and fit a new oil guard flush with the crankcase

from the pulley side.

Refitting the hub bearings

- Install the three shafts in the engine crankcase as shown in the figure.

Vespa GTV 125

Engine

ENG - 21

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды