VESPA GTV 125 Скачать руководство пользователя страница 58

Страница: 58 / 278

This section makes it possible to find what solutions to apply when troubleshooting.

For each breakdown, a list of the possible causes and respective interventions is given.

Engine

Poor performance

POOR PERFORMANCE

Possible Cause

Operation

The carburettor is dirty; fuel pump or vacuum valve

damaged

Remove, wash with solvent and dry with com-

pressed air or replace

Incorrect timing or worn timing system elements

Time the system again or replace the worn parts

Muffler obstructed

Replace

Air filter blocked or dirty

Remove the sponge, wash with water and car

shampoo, then soak it in a mixture of 50% petrol

and 50% specific oil. Press with your hand without

squeezing, allow it to drip dry and refit.

Automatic starter failure

Check: mechanical movement, electric connec-

tion and power supply, replace if required.

Oil level exceeds maximum

Check for causes and fill to reach the correct level

Lack of compression parts, cylinder and valves

wear

Replace the worn parts

Transmission belt worn

Replace

Inefficient automatic transmission

Check the rollers and the pulley movement, re-

place the damaged parts and lubricate the driven

pulley moveable guide with Montblanc Molybde-

num Grease

Clutch slipping

Check the clutch system and/or the bell and re-

place if necessary

Carburettor nozzles clogged

Dismantle, wash with solvent and dry with com-

pressed air

Rear wheel spins at idle

REAR WHEEL ROTATES WITH ENGINE AT IDLE

Possible Cause

Operation

Idling rpm too high

Adjust the engine idle speed

Clutch fault

Check the springs / clutch masses

Intake coupling cracked or clamps incorrectly

tightened

Replace the intake coupling and check the clamps

are tightened

Starting difficulties

DIFFICULTY STARTING UP

Possible Cause

Operation

Altered fuel characteristics

Drain off the fuel no longer up to standard; then,

refill

Rpm too low at start-up or engine and start-up

system damaged

Check the starter motor, the system and the torque

limiter

Troubleshooting

Vespa GTV 125

TROUBL - 2

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды