VESPA GTV 125 Скачать руководство пользователя страница 56

Страница: 56 / 278

- Check that the SAS valve plastic support is not

dented or distorted

- Check that the gasket is in good conditions

- Carefully clean the inside and outside filters. Re-

place them if damaged or abnormally distorted.

- Make sure the coupling connecting the secon-

dary air to the head is not dented, overheated or

distorted. If there is, replace it.

- Check that the metal pipe does not have any

dents

CAUTION

INADEQUATE TIGHTNESS BETWEEN THE
SAS VALVE AND ITS SUPPORT INCREASES
NOISE IN THE SAS SYSTEM.

To refit, follow the removal procedure in reverse order being careful to respect the direction of the rubber

coupling connecting the SAS valve and the discharge system

Maintenance

Vespa GTV 125

MAIN - 22

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды