VESPA GTV 125 Скачать руководство пользователя

Страница: 196 / 278

- Install a new silent bloc, making sure it aligns

properly with the reference tooth.

- Fit the silent blocs, making sure the chamfered

part of the silent bloc matches the chamfered part

of the bracket

- Using the appropriate tool, fit the silent bloc as

shown in the photo

Refitting

- To refit, perform the removal operations in reverse.

- Grease the bearings and the rolling parts with the recommended grease.

-Complete the fitting by tightening the nuts on the relative bolts to the proper tightening torque.

Locking torques (N*m)

Engine and vehicle side swinging arm junction bolt

33 ÷ 41 Nm

Swinging arm pin - Engine

64 -

Body shell - Swinging arm pin

76 ÷ 83

Screw fixing the silent-block support plate to the

body

42 ÷ 52

Shock absorbers

Removal

Proceed as follows:

- place the scooter on its centre stand;

- remove the luggage rack

- lift the engine a little with a jack so as to free the

two shock absorbers;

- remove the muffler assembly;

- undo the shock absorber spring assembly clamp-

ing screw from the support fixed to the engine on

Suspensions

Vespa GTV 125

SUSP - 20

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды