VESPA GTV 125 Скачать руководство пользователя

Страница: 123 / 278

Removing the flywheel magneto

- Lock the rotation of the Flywheel with the calliper

spanner tool.

- Remove the nut.

- Take out the flywheel.

CAUTION

THE USE OF A CALLIPER SPANNER OTHER
THAN THE ONE SUPPLIED COULD DAMAGE
THE STATOR COILS

N.B.

THE FLYWHEEL OF THE 200 CM³ MODELS
FEATURES ENHANCED INERTIAL MASS.

Inspecting the flywheel components

- Check the integrity of the internal plastic parts of the flywheel and the Pick-Up control plate.

Refitting the flywheel magneto

- Fit the flywheel being careful to insert the key

properly.

- Lock the flywheel nut to the prescribed torque

- Check that the Pick-Up air gap is between 0.34

÷ 0.76 mm.

The air gap cannot be modified when assembling

the Pick-Up.

Different values result from deformations visible

on the Pick-Up support.

N.B.

A VARIATION IN THE AIR GAP DISTANCE
MODIFIES THE IGNITION SYSTEM IDLE
SPEED

Specific tooling

020565Y

Flywheel lock calliper spanner

Locking torques (N*m)

Vespa GTV 125

Engine

ENG - 25

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды