VESPA GTV 125 Скачать руководство пользователя страница 76

Страница: 76 / 278

3-FLASH CODE -

Example with programmed control unit, aerial working properly and unknown trans-

ponder code.

Ignition disabled-Vehicle immobilised

Diagnostic code - 2 flashes

Diagnosis code: 2-flashes

When the 2-flash code is detected, carry out the following checks:

- Check if the failure continues after changing key (MASTER key included). If the failure persists with

any key, disconnect the aerial connector from the control unit and check the aerial continuity with the

020331Y multimeter.

If non-conforming values are measured, replace the aerial.

If no failures are found in the aerial, replace the control unit.

CAUTION

BEFORE PROGRAMMING THE NEW ELECTRONIC CONTROL UNIT CHECK THAT NO FAILURE
CODE IS INDICATED. THIS IS NECESSARY TO AVOID SPOILING A NEW CONTROL UNIT

Electric characteristic

immobilizer aerial

~ 7 ÷ 9 Ohm

Diagnostic code - 3 flashes

If the 3-flash code is detected, check if the failure

occurs when the MASTER key in inserted into the

key switch.

- If the failure disappears when the MASTER key

is used, encode the service keys (Blue) again.

- If the failure persists, it means that the MASTER

key and the control unit are not linked; in this case,

replace the control unit and then encode the keys.

The immobilizer system is efficient when, after

switching over to "ON", only a 0.7-second flash is

detected (see diagram).

In this case, the engine can be started.

Electrical system

Vespa GTV 125

ELE SYS - 12

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды