VESPA GTV 125 Скачать руководство пользователя страница 184

Страница: 184 / 278

- Use the specific tool to fit the fifth wheel fitting on

the headstock as indicated in the figure

Specific tooling

020037Y

Punch

- Remove the steering tube

- Remove the attachment bracket

- Use the specific tool with the part 1 and operate

the handgrip until removing temporarily the pin and

the Nadella opposite the tool thrusting direction.

- To extract the second Nadella, use the tool with

the part 2, instead of part 1, on opposite side to the

one indicated in the figure.

Specific tooling

020021Y

Front suspension service tool

- Fit the two dust guard rings "

" on the swinging

hub as shown in drawing "

- Connect the swinging hub to the steering tube

with the guiding pin, part 5.

- Use the specific tool fitted with part 3 on the stem

and part 4 on the tool base.

- Lubricate the pin with Z2 grease and insert it

temporarily on the swinging hub, move the tool

handgrip until part 3 is fully inserted on the steering

tube.

- Once the pin has been fitted, insert the two

spacers part 17 slightly hitting with a mallet (see

next figure).

CAUTION

USE NEW ROLLER CASINGS, PIN, SEALING
RINGS AND DUST GUARDS FOR REFITTING.

Specific tooling

020021Y

Front suspension service tool

Suspensions

Vespa GTV 125

SUSP - 8

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды