manualshive.com logo in svg

VESPA GTV 125, Руководство по обслуживанию станции

Поделиться
Скачать
VESPA GTV 125 Скачать руководство пользователя страница 203

Removal

- Remove the front wheel

- Pre-loosen the two fixing pins of the brake pads

- Remove the two front brake calliper devices fas-

tening them to the support as shown in the photo-

graph.

N.B.

WHEN A PROCEDURE IS PLANNED INCLUD-
ING THE SERVICE OR REPLACEMENT OF THE
CALLIPER, FIRST LOOSEN THE FITTING CON-
NECTING THE PIPE TO THE BRAKE CALLIPER

Overhaul

Proceed as follows:

1) remove the two male hexagonal screws (1) and

take out the two pads (10);

2) remove the two male hexagonal screws (2) and

remove the reaction plate (3);

3) take out the fixed plate (4) from the guide;

4) remove the internal elements from the floating

body (5) with the help of short blows of com-

pressed air through the brake fluid pipe in order to

facilitate the expulsion of pistons (6).

5) Check:

- that the plates and the body are whole and in

good condition;

- that the cylinder and the floating body of the cal-

liper do not show signs of scratches or erosion,

otherwise replace the entire calliper;

- that the guides of the fixed plate are not scratched

or eroded, otherwise replace the entire plate;

Vespa GTV 125

Braking system

BRAK SYS - 5

Содержание GTV 125























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды