VESPA GTV 125 Скачать руководство пользователя

Страница: 112 / 278

Inspecting the rollers case

- Check that the internal bushing shown in the fig-

ure is not abnormally worn and measure inner

diameter A.

- Measure outer diameter B of the pulley sliding

bushing shown in the figure.

- Check that the rollers are not damaged or worn.

- Check the guide shoes for the variator back-plate

are not worn.

- Check the wear of the roller housings and of the

belt contact surfaces on both pulley halves.

- Check that stationary driving pulley does not

show signs of abnormal wear on the grooved edge

and on the surface in contact with the belt.

- Check that the O-ring is not pushed out of shape.

CAUTION

DO NOT LUBRICATE OR CLEAN SINTERED
BUSHINGS

Characteristic

Movable driving half-pulley bushing: Standard
Diameter

26.000 - 26.021 mm

Movable driving half-pulley bushing: Maxi-
mum allowable diameter

Ø 26.12 mm

Sliding bushing: Standard Diameter

Ø 25.959 ÷ 25.98 mm

Sliding bushing: Minimum admissible diame-
ter

Ø 25.95 mm

Roller: Standard Diameter

Ø 18.9 ÷ 19.1 mm

Roller: Minimum diameter permitted

Ø 18.5 mm

Engine

Vespa GTV 125

ENG - 14

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды