VESPA GTV 125 Скачать руководство пользователя

Страница: 50 / 278

Level check

The brake fluid tanks for the front and rear brakes

are located on the pumps under the handlebar

cover. Proceed as follows:

- Remove the brake pump cover

- Rest the vehicle on its centre stand with the han-

dlebars perfectly horizontal;

- Check the fluid level through the sight glass as

shown in the figure. A certain lowering of the level

is caused by wear on the pads.

Top-up

- Position the vehicle on a flat surface and on the

centre stand

- Remove the brake pump cover as indicated in the

photo

Check the brake fluid level through the sight glass

on the pump as shown in the photograph

- If the level is below the minimum, fill using the two

screws shown in the figure

- Remove the gasket and fill with DOT 4 until the spyglass is completely covered

For refitting purposes carry out the operations in the reverse order from the removal operation and

respect the tightening torque of the tank cover screws.

CAUTION

MAKE SURE THE BRAKE FLUID DOES NOT GET INTO YOUR EYES OR ON YOUR SKIN OR
CLOTHES. IF THIS HAPPENS ACCIDENTALLY, WASH WITH WATER.

CAUTION

THE BRAKING CIRCUIT FLUID IS HIGHLY CORROSIVE. THEREFORE, WHEN TOPPING IT UP,
AVOID LETTING IT COME INTO CONTACT WITH THE PAINTED PARTS OF THE VEHICLE. THE

Maintenance

Vespa GTV 125

MAIN - 16

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды