manualshive.com logo in svg

VESPA GTV 125, Руководство по обслуживанию станции


Поделиться
Скачать
background image

Removing the driven pulley shaft bearing

When removing the driven pulley shaft, the corre-

sponding bearing and oil seal, remove the trans-

mission cover and the clutch group as explained

above.

- Extract the driven pulley shaft from its bearing.

- Remove the oil guard using a screwdriver, work-

ing from inside the bearing and being careful not

to damage the housing, make it come out of the

belt transmission side.

- Remove the seeger ring shown in the figure

With the sectional punch, remove the driven pulley

shaft bearing.

Specific tooling

020376Y

 

Adaptor handle

020375Y

 

Adaptor 28 x 30 mm

020363Y

 

20 mm guide

Inspecting the hub shaft

- Check the three shafts for wear or distortion of

the toothed surfaces, the bearing housings, and

the oil seal housings.

- In case of anomalies, replace the damaged com-

ponents.

Inspecting the hub cover

- Check that the fitting surface is not dented or distorted.

- Check the bearing bearings.

- In case of anomalies, replace the damaged components.

Vespa GTV 125

Engine

ENG - 19

Содержание GTV 125























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GTV 125

Invacare Pronto Air User Manual preview
Pronto Air
Бренд: Invacare Страницы: 64
Speedlion 84036 Quick Start Manual preview
84036
Бренд: Speedlion Страницы: 9
King Song N1-A User Manual preview
N1-A
Бренд: King Song Страницы: 48
Sterling Elite2 Plus Instructions For Use Manual preview
Elite2 Plus
Бренд: Sterling Страницы: 52
Hover-1 H1-MFEB Operation Manual preview
H1-MFEB
Бренд: Hover-1 Страницы: 22
Hover-1 Gambit Operation Manual preview
Gambit
Бренд: Hover-1 Страницы: 27
Trikke Pon-e 48V Owner'S Manual preview
Pon-e 48V
Бренд: Trikke Страницы: 36
EVO Powerboards Evo R Owner'S Manual preview
Evo R
Бренд: EVO Powerboards Страницы: 16
Lemeego X E-Bike 2021 Manual preview
X E-Bike 2021
Бренд: Lemeego Страницы: 2
Gazelle with BOSCH System User Manual preview
with BOSCH System
Бренд: Gazelle Страницы: 40
Isel EuroScooter Owner'S Manual preview
EuroScooter
Бренд: Isel Страницы: 8
X-TREME XR-101 Product Handbook preview
XR-101
Бренд: X-TREME Страницы: 12
X-TREME XG-575DS Owner'S Manual preview
XG-575DS
Бренд: X-TREME Страницы: 17
X-TREME X-600 Owner'S Manual preview
X-600
Бренд: X-TREME Страницы: 32
X-TREME X-250 User Manual preview
X-250
Бренд: X-TREME Страницы: 30
Yedoo Wzoom New User Manual preview
Wzoom New
Бренд: Yedoo Страницы: 19
Jetson JOURNEY Manual preview
JOURNEY
Бренд: Jetson Страницы: 24
Yamaha XMAX 125i 2005 Owner'S Manual preview
XMAX 125i 2005
Бренд: Yamaha Страницы: 76

Бренды по названию

Популярные бренды

Загрузить еще бренды