manualshive.com logo in svg

VESPA GTV 125, Руководство по обслуживанию станции


Поделиться
Скачать
background image

- Insert the flywheel cover with bearings on the ap-

propriate tool.

- Insert the shaft together with the mechanical gas-

kets on the bearings.

- With the appropriate punch and socket, insert the

shaft in the bearings and the drive until the end of

stroke of the appropriate tool cannot be seen.

N.B.

CENTRE THE PUNCH CORRECTLY ON THE
ROTOR. PUSH THE SHAFT IN AND CHECK
THAT THE FLYWHEEL COVER ROTATES
SMOOTHLY. FAILURE TO RESPECT THIS
PROCEDURE DAMAGES THE DRIVE.

- Reassemble the rotor cover with a new O-Ring.

-Tighten the 3 fixing screws to the torque below:

N.B.

DO NOT LUBRICATE THE O-RING. FAILURE
TO RESPECT THIS RULE RESULTS IN RING
DISTORTION.

Locking torques (N*m)

Water pump cover screws

 

3 ÷ 4

Component check

- Check that the rotor does not show abnormal wear or dents;

- Check that the rotor shaft is not rusty;

- Check that there is no rust on the bearing seats or the ceramic seal;

- Check that the drive does not show dents and that it is perfectly integral with the steel hub.

Removal

- Check the water pump if noise in the bearings or liquid leaking from the drainage hole inside the cover

is detected.

-Remove the flywheel cover together with the water pump from the engine.

- Remove the rotor cover by unscrewing the 3 retainers indicated in the figure.

Vespa GTV 125

Cooling system

COOL SYS - 3

Содержание GTV 125























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GTV 125

VMAX 110.52598 User Manual preview
110.52598
Бренд: VMAX Страницы: 24
X-TREME scooter XB-504 Owner'S Manual preview
XB-504
Бренд: X-TREME scooter Страницы: 31
Denver SEL-80130F User Manual preview
SEL-80130F
Бренд: Denver Страницы: 23
AREBOS AR-HE-TSB Manual preview
AR-HE-TSB
Бренд: AREBOS Страницы: 8
Emos RAP CT KARGO Bange Operation Manual preview
RAP CT KARGO Bange
Бренд: Emos Страницы: 88
F-Wheel DYU D3F Instruction preview
DYU D3F
Бренд: F-Wheel Страницы: 6
E Rider City 30 User Manual preview
City 30
Бренд: E Rider Страницы: 8
Abilize Vapor X75 Instruction Booklet preview
Vapor X75
Бренд: Abilize Страницы: 20
King Song N1-A User Manual preview
N1-A
Бренд: King Song Страницы: 48
Oxybul FREEBUL 336367 Manual preview
FREEBUL 336367
Бренд: Oxybul Страницы: 13
AddBike U-Cargo Functional Check Instructions preview
U-Cargo
Бренд: AddBike Страницы: 3
Aovo AovoPro Manual preview
AovoPro
Бренд: Aovo Страницы: 27
Trikke Pon-e 48V Owner'S Manual preview
Pon-e 48V
Бренд: Trikke Страницы: 36
Hover-1 Liberty Operation Manual preview
Liberty
Бренд: Hover-1 Страницы: 24
Razor Jr. Lil' E Manual preview
Lil' E
Бренд: Razor Jr. Страницы: 9
Razor UB1 Owner'S Manual preview
UB1
Бренд: Razor Страницы: 20
Razor Jr. t3 Manual preview
t3
Бренд: Razor Jr. Страницы: 52
DENAGO Model 1 Owner'S Manual preview
Model 1
Бренд: DENAGO Страницы: 77

Бренды по названию

Популярные бренды

Загрузить еще бренды