VESPA GTV 125 страница 158 Скачать руководство пользователя

Страница: 158 / 278

Crankshaft oil seals

Refitting

- Fit the internal bulkhead by locking the two

screws to the prescribed torque.

- Fit the oil filter fitting and tighten it to the specified

torque.

- Place a new gasket on one of the crankcase

halves, preferably on the transmission side, to-

gether with the locating dowels.

- Lubricate the main bushings and insert the crank-

shaft in the transmission side crankcase half.

- Reassemble the two crankcase halves.

- Fit the 11 screws and tighten them to the pre-

scribed torque.

- Lubricate the flywheel oil seal.

- Using the appropriate tool, assemble the oil seal.

- Fit a new O-ring on the pre-filter and lubricate it.

- Insert the filter on the engine with the relative cap.

Tighten to the specified torque.

N.B.

FAILURE TO USE THE SPECIFIC TOOL CAN
RESULT IN AN INCORRECT DEPTH POSITION
AND AS A CONSEQUENCE IN INADEQUATE
OIL SEALING.

Specific tooling

020425Y

Punch for flywheel-side oil seal

Locking torques (N*m)

Internal engine crankcase bulkhead (transmis-
sion-side half shaft) screws

4 ÷ 6

Oil filter on

crankcase fitting

27 ÷ 33

Engine-crankcase

coupling screws

11 ÷ 13

Engine oil drainage

plug/mesh filter

24 ÷ 30

Engine

Vespa GTV 125

ENG - 60

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды