VESPA GTV 125 Скачать руководство пользователя

Страница: 160 / 278

Inspecting the by-pass valve

- Check the unloaded spring length.

- Check that the small piston is not scored.

- Ensure that it slides freely on the crankcase and that it guarantees a good seal.

- If not, eliminate any impurities or replace defective parts.

Characteristic

By-pass check up: Standard length

54.2 mm

Refitting the oil sump

- Refit the by-pass valve plunger in its housing.

- Insert the pressure-regulating spring.

- Fit a new sump seal.

- Refit the two centring dowels.

- Refit the sump, taking care to locate the spring in

the appropriate recess machined into the inside of

the sump.

- Refit the rear brake cable brackets and the

screws in the reverse order from which they were

removed.

- Tighten the screws to the prescribed torque.

- Refit the driving pulley assembly, the drive belt,

the sprocket wheel and the transmission cover, as

described in the "Transmissions" chapter.

- When testing the lubrication system, refer to

chapter "Crankcase and Crankshaft", regard-

Engine

Vespa GTV 125

ENG - 62

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды