VESPA GTV 125 Скачать руководство пользователя

Страница: 187 / 278

- Remove the steering tube

- Remove the attachment bracket

- Use the specific tool with the part 1 and operate

the handgrip until removing temporarily the pin and

the Nadella opposite the tool thrusting direction.

- To extract the second Nadella, use the tool with

the part 2, instead of part 1, on opposite side to the

one indicated in the figure.

Specific tooling

020021Y

Front suspension service tool

Refitting

To refit, carry out the removal operations but in reverse order; grease the fifth wheel fittings and tighten

at the specified locking torques

Locking torques (N*m)

Handlebar to steering tube

45 ÷ 50 Nm

Upper steering ring nut

30 ÷ 40

Lower steering ring nut

8 ÷ 10

Front shock absorber

Removal

- Remove the steering tube

- Remove the shock absorber lower clamps

- Remove the shock absorber upper clamps

Refitting

To refit, carry out the removal operations in reverse order, observing the prescribed tightening torques.

Locking torques (N*m)

shock absorber lower clamp

20 - 27 Nm

shock absorber upper clamp

20 ÷ 30

Vespa GTV 125

Suspensions

SUSP - 11

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды