VESPA GTV 125 Скачать руководство пользователя

Страница: 162 / 278

Inspecting the cut-off

- Remove the SAS valve.

- Connect the MITYVAC pump in low-pressure

mode (VACUUM) to the CUT-OFF valve vacuum

intake.

- Apply a vacuum value higher than 0.5 BAR.

- Check that this value is kept all the time.

- If a worn seal is detected, replace it.

- With a "T" bypass and flexible rubber hoses make

a parallel connection between the rubber coupling

and the vacuum intake of the CUT-OFF valve.

- Connect the bypass to the MITYVAC pump.

- Set the pump set to the low-pressure mode

(VACUUM).

- Using a pair of long flat pliers, choke the rubber

hose next to the valve.

- Operate the pump until vacuum is higher than 0.5

BAR.

- Release the hose and check how the vacuum re-

acts. - Under normal functioning conditions the

vacuum undergoes a slight fall and then readjusts.

There follows a slow and continuous loss of de-

pression up to approximately 0.4 BAR. At this point

the valve opens and the depression is suddenly

set to zero.

Lack of tightness or the fact that the valve opens

at different vacuum values should be regarded as

anomalies. In this case, replace it.

N.B.

LACK OF TIGHTNESS IN THE CUT-OFF VALVE
RESULTS IN EXHAUST NOISE (EXPLOSIONS
IN THE MUFFLER). INCORRECT CUT-OFF
VALVE CALIBRATION CAN RESULT IN CATA-
LYTIC CONVERTER MALFUNCTIONING

N.B.

A FAULTY CUT-OFF VALVE DIAPHRAGM, BE-
SIDES JEOPARDISING THE CORRECT OPER-
ATION OF THE CUT-OFF VALVE, ALSO DAM-
AGES IDLE FUNCTIONING

Specific tooling

Engine

Vespa GTV 125

ENG - 64

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды