VESPA GTV 125 Скачать руководство пользователя

Страница: 153 / 278

Inspecting the crankshaft plain bearings

- T

o obtain a good bushing lubrication it is necessary

to have both an optimal lubricating pressure (3,2

bar) and a good oil flow rate; the bushings must be

correctly positioned so as not to obstruct the oil

supply channels.

- The main bushings are comprised of two half-

bearings, one with holes and channels for lubrica-

tion whereas the other is solid.

- The solid half-bearing is intended to stand the

thrusts caused by combustion, and for this reason

it is arranged opposite the cylinder.

- To prevent obstructions in the oil feeding chan-

nels, the matching surface of the two half-bearings

must be perfectly perpendicular to the cylinder ax-

is, as shown in the figure.

- The oil feeding channel section is also affected

by the bushings driving depth compared with the

crankshaft axial clearance of the limiting surface.

- Check the inside diameter of the main bushings

in the three directions indicated in the diagram.

- Repeat the measurements for the other bushing

half. see diagram.

- There are three crankcase versions: with RED

main bushings, with BLUE main bushings and with

YELLOW main bushings.

- There is only one type of main bushing housing

hole in the crankcase

The standard bushing diameter after driving is var-

iable on the basis of a coupling selection.

- The bushing housings in the crankcase are avail-

able in two categories, Cat. 1 and Cat. 2, as are

the crankshafts.

- The main bushings are available in three thick-

ness categories, identified by colour markings, as

shown in the table below.

Vespa GTV 125

Engine

ENG - 55

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды