VESPA GTV 125 Скачать руководство пользователя

Страница: 139 / 278

Inspecting the valve housings

- Check the width of the imprint on the valve

seat«

» wear limit max. 1.6 mm.

- Remove any carbon formation from the valve

guides.

- Measure the inside diameter of each valve guide.

- Take the measurement at three different heights

in the rocker arm push direction.

- If the width of the impression on the valve seat or

the diameter of the valve guide exceed the speci-

fied limits, replace the cylinder head.

Characteristic

Valve seat wear Intake guide

limit accepted: 5.022

Valve seat wear Intake guide

Standard diameter: 5.000 ÷ 5.012 mm

Valve seat wear Exhaust guide

Accepted limit 5.022

Valve seat wear Exhaust guide

Standard diameter: 5.000 ÷ 5.012 mm

Inspecting the valves

- Measure the diameter of the valve stems in the

three positions indicated in the diagram.

- Calculate the clearance between valve and valve

guide.

- Check that there are no signs of wear on the sur-

face of contact with the articulated register termi-

nal.

- If the checks above give no failures, you can use

the same valves. For best sealing results, it is ad-

visable to grind the valves. Grind the valves gently

with a fine-grained lapping compound. During the

grinding, keep the cylinder head with the valve ax-

es in a horizontal position. This will prevent the

lapping compound residues from penetrating be-

tween the valve stem and the guide (see figure).

Vespa GTV 125

Engine

ENG - 41

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды