VESPA GTV 125 Скачать руководство пользователя

Страница: 136 / 278

Refitting the piston rings

- Place the oil scraper spring on the piston.

- Refit the oil scraper ring with the join of spring

ends on the opposite side from the ring gap and

the word 'TOP' towards the crown of the piston.

The chamfered side of the oil scraper ring should

always be facing the piston crown.

- Fit the middle piston ring with the identification

letter facing the crown of the piston. In any case,

the step must be facing opposite the piston top.

- Fit the top piston ring with the word 'TOP' or the

reference mark facing the crown of the piston.

- Offset the piston ring gaps on the three rings by

120° to each other as shown in the figure.

- Lubricate the components with engine oil.

N.B.

THE TWO PISTON RINGS ARE MADE WITH A
TAPERED CYLINDRICAL CONTACT CROSS-
SECTION. THIS IS TO ACHIEVE A BETTER
BEDDING.

Refitting the cylinder

- Insert the cylinder base gasket with the thickness determined above.

- Using the fork support and the piston ring retaining band, refit the cylinder as shown in the figure.

N.B.

BEFORE FITTING THE CYLINDER, CAREFULLY BLOW OUT THE LUBRICATION DUCT AND OIL
THE CYLINDER BARREL.

Specific tooling

020393Y

Piston fitting band

020287Y

Clamp to assemble piston on cylinder

Engine

Vespa GTV 125

ENG - 38

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды