VESPA GTV 125 Скачать руководство пользователя страница 216

Страница: 216 / 278

Water pump - overhaul

Water pump assembly

With a hot air gun heat the inner side of the fly-

wheel cover.

AVOID OVERHEATING AS THIS MAY ALTER
THE PAINTED SURFACE.

Specific tooling

020151Y

Air heater

- Place the flywheel cover on the ring base following the same procedure as for removal.

- Place the two bearings on the specific punch.

N.B.

USE A NEW BEARING WHEN REFITTING

- Use grease to keep the bearings on the appropriate tool.

- Use a plastic mallet to insert the bearings on the housing up to the stop.

- Assembly the ceramic ring and the correspond-

ing rubber gasket. The ceramic ring chamfering

should always face towards the gasket.

- Lubricate the rubber gasket and insert the unit on

the flywheel cover.

Use the punch of the appropriate tool manually if

necessary.

ALWAYS USE NEW CERAMIC RING AND GAS-
KETS. ASSEMBLING THE CERAMIC SEALING
RING IN A MANNER OTHER THAN MANUALLY
MAY DAMAGE THE RING.

Specific tooling

020440Y

Water pump service tool

- Insert the drive on the guide pin of the support

base which is part of the appropriate tool. Check

that the convex part faces upwards.

Cooling system

Vespa GTV 125

COOL SYS - 2

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды