VESPA GTV 125 Скачать руководство пользователя

Страница: 209 / 278

- Screw the two pad lock pins to the correct torque, and apply the recommended product.

- Fit the calliper on its support, tightening the two screws to the prescribed torque.

N.B.

IF IT IS NOT POSSIBLE TO CORRECTLY POSITION THE CALLIPER ON THE DISC DURING FIT-
TING, GENTLY EXPAND THE PADS.

Recommended products

Loctite 243

Medium strength threadlock

Loctite 243 medium-strength threadlock

Locking torques (N*m)

Screw tightening calliper to the support

20 ÷ 25

Pad fastening pin

19.6 ÷ 24.5

Rear brake pads

Removal

- Remove the rear brake calliper.

- Remove the brake pad and check there are no

faults or warping. If there is, replace it.

- Check the thickness of the friction material is

more than 1.5 mm. If it is not , replace it

- The replacement must be made with greater re-

sidual thickness if the pad has not worn evenly. A

0.5 mm thickness difference in the residual friction

material is permitted

Vespa GTV 125

Braking system

BRAK SYS - 11

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды