VESPA GTV 125 Скачать руководство пользователя страница 193

Страница: 193 / 278

- To check the clearance on the frame-side arm,

mount the retainer using the pin fixing the swinging

arm to the frame and two adaptor rings of the ap-

propriate tool 020229Y. Alternatively use two

washers with inner diameter for 12-mm pins, min.

outer diameter: 30 mm: min. thickness: 4 mm.

- Check there is no sticking in the rotation.

- Check the axial clearance of the swinging arm on

the frame side

Characteristic

Standard clearance

0.40 ÷ 0.60 mm

Allowable limit after use:

1.5 mm

- Separate the swinging arm on the engine side

from the vehicle side arm.

- Remove the plastic bushings and the internal

spacer shown in the photo.

- Using a suitable pin remove the roller casings as

shown in the photographs

Vespa GTV 125

Suspensions

SUSP - 17

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды