VESPA GTV 125 Скачать руководство пользователя страница 122

Страница: 122 / 278

Refitting the stator

- Refit the stator and flywheel carrying out the re-

moval procedure in reverse, tightening the retain-

ers to the prescribed torque.

- Place the cable harness as shown in the figure.

- Stator screws and Pick-Up

N.B.

THE PICK-UP WIRE SHOULD BE POSITIONED
BETWEEN THE UPPER SCREW AND THE REF-
ERENCE PIN AS SHOWN IN THE DETAIL
DRAWING.

Locking torques (N*m)

Stator assembly screws (°)

3 ÷ 4

Refitting the flywheel cover

- Place the flywheel with the top dead centre mark

aligned with the crankcase.

- Place the flywheel cover by aligning the reference

marks of the drive and the crankcase cover.

- Reassemble the cover on the engine, placing the

three connectors in the drive for the water pump.

- Carry out the steps in the reverse order from the

dismantling procedure.

CAUTION

TAKE CARE TO CORRECTLY POSITION THE
FLYWHEEL CONNECTOR. MAKE SURE THE
CENTRING DOWELS ARE PRESENT.

Flywheel and starting

- Check the integrity of the internal plastic parts of the flywheel and the Pick-Up control plate.

Engine

Vespa GTV 125

ENG - 24

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Бренды по названию

Популярные бренды