VESPA GTV 125 Скачать руководство пользователя

Страница: 80 / 278

Stator check

- With a tester, check the circuit between connec-

tions 5-3 and 5-1 is not interrupted.

- Check the earth isolation on the three phases of

stators 5-earth, 3-earth, 1-earth.

Stage indicative resistance: 0.7 - 0.9

Ω

Minimum oil pressure switch check

- With a tester, check the circuit between connec-

tions 4 and ground (with engine off) is not inter-

rupted.

Pick-Up check

- Check that there is a resistance of about 105 ÷

124

Ω

at 20° C between connection 2 and ground.

- In case of values different from the ones stated,

replace the defective parts.

N.B.

VALUES ARE STATED AT AMBIENT TEMPER-
ATURE. A CHECK WITH THE STATOR AT OP-
ERATING TEMPERATURE MAY RESULT IN
VALUES HIGHER THAN THOSE STATED.

Disconnect the connector from the voltage regulator and check there is continuity between any yellow

cable and the other two cables.

Electric characteristic

Ohm value:

0.7 ÷ 0.9 Ohm

Also check that all yellow cables are insulated from

the ground connection.

If non-conforming values are detected, repeat the

checks directly to the stator. In case of further rep-

etitions of incorrect values replace the stator or

repair the wiring.

Electrical system

Vespa GTV 125

ELE SYS - 16

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды