VESPA GTV 125 Скачать руководство пользователя

Страница: 52 / 278

SAS filters inspection and cleaning

the SAS for leader engines 125 cm³ - 200 cm³ Euro

2 operates in a similar manner to the SAS for 2T

engines.

The differences are the following:

instead of entering through the muffler as for 2T

engine, the secondary air enters directly in the dis-

charge pipe on the head.

The 2T reed valve has a diaphragm. The unit, in-

dicated by an arrow in the figure, has a cut-off

connected to the depression intake on the inlet

manifold that cuts the air inlet in deceleration, to

avoid explosions in the muffler.

System description:

Air is drawn through the opening "

", goes through

the first filter and is channelled through the open-

ing "

Air gets to the second filter "

" through the opening

indicated in the figure.

Now, the filtered air enters the diaphragm device,

and then is channelled to the head.

Maintenance

Vespa GTV 125

MAIN - 18

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды