VESPA GTV 125 Скачать руководство пользователя

Страница: 109 / 278

Inspecting the clutch spring

- Measure the length of the movable driven half-

pulley spring while it is unloaded.

Characteristic

Standard length

106 mm

acceptable limit after use:

101 mm

Refitting the clutch

- Support the driven pulley spring compressor ap-

propriate tool with the control screw in vertical axis.

- Arrange the tool with the medium length pins

screwed in position «

» on the inside.

- Insert the adapter ring 8 in the pins.

- Preassemble the cooling fan to the clutch in such

a way that the keying facets are aligned and the 3

pin heads (A) of the mass axis can be seen in full.

- Insert the clutch on the adapter ring.

- Lubricate the end of the spring that abuts against

the servo-system closing collar.

- Insert the spring with its plastic holder in contact

with the clutch.

- Insert the driving belt into the pulley unit accord-

ing to their direction of rotation.

- Insert the pulley unit with the belt into the tool.

- Slightly preload the spring.

- Make sure that the clutch is perfectly inserted into

the adapter ring before proceeding to tighten the

clutch nut.

- Place the tool in the clamp with the control screw

on the horizontal axis.

- Fully preload the spring.

- Apply the clutch lock nut and tighten it to the

specified torque using the specific 46x55 spanner.

Vespa GTV 125

Engine

ENG - 11

Содержание GTV 125























































































































































































































































































Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды

VESPA GTV 125, Руководство по обслуживанию станции

Результаты поиска

Содержание GTV 125

Отзывы:

Похожие инструкции для GTV 125

Бренды по названию

Популярные бренды