manualshive.com logo in svg

Vacon NX, Руководство пользователя

Vacon NX - это мощный преобразователь частоты, предоставляющий быструю помощь с помощью бесплатного руководства. Скачайте руководство с нашего сайта для получения подробной информации о продукте. {Website} - ваш источник полезных ресурсов для вашего оборудования.

Поделиться
Скачать
background image

5

vacon • 36

Installation

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

5.

I

NSTALLATION

5.1

Mounting

VACON

®

 NX Liquid-Cooled Drive modules must be installed into an enclosure. The drives consisting 

of one module will be mounted on the mounting plate. The drives that include two or three modules 
are mounted inside a mounting bracket (see table below) which will then be installed in the 
enclosure.

NOTE! If any other than vertical installation position is required, contact your distributor!

NOTE! 

The allowed installation temperature is 0...+70 °C.

In Chapter 5.1.2  you will find the dimensions of VACON

®

 NX Liquid-Cooled drives installed on 

mounting bases (plates and brackets).

5.1.1

Lifting the drive

We recommend you to always use a jib crane or similar elevating device to lift the AC drive/ inverter 
unit. See figures below for correct lifting points.

For units with no mounting bracket (see Chapter 5.1.2.1), the best place for hoisting is the hole(s) in 
the middle of the mounting plate (Lifting point 1). VACON

®

 NX Liquid-Cooled drives consisting of 

several modules can the most safely and easily be lifted by the holes in the mounting bracket (Lifting 
point 2) using a screw pin shackle. Pay also attention to the recommended dimensions of the 
hoisting belt and the beam. See Figure 3.

Figure 3.  Lifting points for drives consisting of one module (left) and several modules

In cabinet installation, the hoisting procedure described above right may, however, become difficult 
or even impossible if the cabinet width does not allow the use of the screw pin shackle in Lifting 
point 2 (see above). 

nxw7.fh8

Lifting point 1
Ø13mm

Hoisting Belt
35 x 1000mm

Beam

1/2" Screw Pin Shackle

Lifting point 2

n88,9 x 5mm

11311_uk

Содержание NX
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX

UE 120 Series Installation And Maintenance Instructions preview
120 Series
Бренд: UE Страницы: 4
XBOX 360 Manual preview
360
Бренд: XBOX Страницы: 7
Danfoss VLT series Quick Manual preview
VLT series
Бренд: Danfoss Страницы: 37
Daikin MicroTech II Operation And Maintenance Manual preview
MicroTech II
Бренд: Daikin Страницы: 44
Salda TPC User Manual preview
TPC
Бренд: Salda Страницы: 16
Elby Designs ASM301-ADSR Diagrams preview
ASM301-ADSR
Бренд: Elby Designs Страницы: 4
Mitsubishi AL-ASI-BD Hardware Manual preview
AL-ASI-BD
Бренд: Mitsubishi Страницы: 16
SOMFY Situo 1 RTS Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 4
Bailey infi 90 IMMFP12 Instruction preview
infi 90 IMMFP12
Бренд: Bailey Страницы: 75
mr. steam iSteam 2.0 Control Installation, Operation & Maintenance Manual preview
iSteam 2.0 Control
Бренд: mr. steam Страницы: 16
Sygonix 2446222 Operating Instructions Manual preview
2446222
Бренд: Sygonix Страницы: 12
IDEATEC DLC4000 User Manual preview
DLC4000
Бренд: IDEATEC Страницы: 32
Broadcast Tools AVR-8 Installation And Operation Manual preview
AVR-8
Бренд: Broadcast Tools Страницы: 15
hotset C 148 Quick Start Manual preview
C 148
Бренд: hotset Страницы: 2
Ultrahaptics STRATOSTM INSPIRE User Manual preview
STRATOSTM INSPIRE
Бренд: Ultrahaptics Страницы: 7
Zeversolar Zeverlution S Setup Manual preview
Zeverlution S
Бренд: Zeversolar Страницы: 8
ECUE DMX2CC 12ch Setup Manual preview
DMX2CC 12ch
Бренд: ECUE Страницы: 39
Regada SP 1 Installation, Service And Maintenance Instructions preview
SP 1
Бренд: Regada Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды