Vacon NX Скачать руководство пользователя страница 199

Страница: 199 / 239

Non-regenerative front end

vacon • 197

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

Input phase

External electronic monitoring relay have
detected undervoltage, phase
sequence or phase failure issue.

•

min. threshold value: 360Vac for
400-500Vac supply voltage

•

min. threshold value: 470Vac for
525-690Vac supply voltage

•

response delay is set to be 0.1 sec

Various causes:

Supply phase failure

Supply fuse failure

Incorrect Mains cabling

Grid interruption

Check EMD relay settings,
Signal wiring, supply volt-
age, fuses, supply cable,
rectifying bridge.

Undertemperature

Power module heatsink temperature is
under –10 °C.

Power module is in a too
cold
place or coolant agent is too
cold. Check the ambient &
coolant temperature. Check
the signal wiring.

Overtemperature

Fault:
Power module heatsink temperature is
over 60 °C.

Warning:
Power module heatsink temperature is
over 55 °C.

•

Check Coolant flow
and temperature

•

Check the ambient
temperature.

•

Check the cooling fan
condition

•

Check the power
module loading

•

Check the signal
wiring

Fan cooling

Jammed cooling fan

Cooling Fan failure

Cooling Fan is not rotating

•

Check the signal
wiring

•

Change the cooling
fans

Ext Fault

External fault digital input have triggered
the fault

•

Check the signal
wiring

•

Check External Fault
input

Choke Temp

Over temperature switch feedback or

Fault:
The temperature of the external input AC
choke is over 130 °C (measured from
PT100 thermistor).

Warning:
The temperature of the external input AC
choke is over 110 °C. (measured from
PT100 thermistor)

•

Check input AC choke
cooling conditions

•

Check the power
module loading

•

Check the signal
wiring

Table 96. Fault codes

Fault

code

Fault

Possible cause

Correcting measures

Содержание NX
















































































































































































































































Результаты поиска

Содержание NX

Отзывы:

Похожие инструкции для NX

Бренды по названию

Популярные бренды

Vacon NX, Руководство пользователя

Результаты поиска

Содержание NX

Отзывы:

Похожие инструкции для NX

Бренды по названию

Популярные бренды