manualshive.com logo in svg

Vacon NX, Руководство пользователя

Vacon NX - это мощный преобразователь частоты, предоставляющий быструю помощь с помощью бесплатного руководства. Скачайте руководство с нашего сайта для получения подробной информации о продукте. {Website} - ваш источник полезных ресурсов для вашего оборудования.

Поделиться
Скачать
background image

3

vacon • 18

Receipt of delivery

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

3.4

Warranty

Only manufacturing defects are covered by the warranty. The manufacturer assumes no 
responsibility for damages caused during or resulting from transport, receipt of the delivery, 
installation, commissioning or use.

The manufacturer shall in no event and under no circumstances be held responsible for damages 
and failures resulting from misuse, wrong installation, unacceptable ambient temperature, running 
motor with lower coolant flow than minimum flow, condensation, dust, corrosive substances or 
operation outside the rated specifications.

Neither can the manufacturer be held responsible for consequential damages.

NOTE!

 VACON

®

 NX Liquid-Cooled drives must not be run with the liquid cooling system 

disconnected. Furthermore, the requirements of the liquid cooling specifications, e.g. minimum 
flow rate (see  Chapter 5.2 and Table 15) must be satisfied. Ignoring this will render the warranty 
null and void.

NOTE! 

VACON

®

 Liquid-Cooled NX_8 inverter unit must be equipped with a du/dt- or sine-filter. The 

warranty is void in case filter are not used with these units. 

The Manufacturer's time of warranty, if not otherwise agreed, is 18 months from the delivery or 12 
months from the commissioning whichever expires first.

The local distributor may grant a warranty time different from the above. This warranty time shall 
be specified in the distributor's sales and warranty terms. Vacon Ltd assumes no responsibility for 
any other warranties than that granted by Vacon itself.

In all matters concerning the warranty, contact first your distributor.

Содержание NX
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX

Dahua NKB User Manual preview
NKB
Бренд: Dahua Страницы: 58
IFM CR710S Original Operating Instructions preview
CR710S
Бренд: IFM Страницы: 49
JENCO 6311 Operation Manual preview
6311
Бренд: JENCO Страницы: 36
jcm-tech WAVE500 User Manual preview
WAVE500
Бренд: jcm-tech Страницы: 8
Z3 Technology Z3-DM8107-SDI-RPS User Manual preview
Z3-DM8107-SDI-RPS
Бренд: Z3 Technology Страницы: 73
Z-Wave Control4 Setup Manual preview
Control4
Бренд: Z-Wave Страницы: 14
Z-Wave.Me KFOB2 Quick Start preview
KFOB2
Бренд: Z-Wave.Me Страницы: 4
Raynor Smart Control Panel 880RGD Quick Manual preview
Smart Control Panel 880RGD
Бренд: Raynor Страницы: 4
Mold-Masters TempMaster M2 Plus Series Quick Manual preview
TempMaster M2 Plus Series
Бренд: Mold-Masters Страницы: 2
Spirax Sarco FTC80 Installation And Maintenance Instructions Manual preview
FTC80
Бренд: Spirax Sarco Страницы: 24
Trinamic TMCM-1240 Hardware Manual preview
TMCM-1240
Бренд: Trinamic Страницы: 30
ZiLOG Z8 Encore! XP Dual F1680 Series User Manual preview
Z8 Encore! XP Dual F1680 Series
Бренд: ZiLOG Страницы: 18
Danfoss AME 56K Instructions Manual preview
AME 56K
Бренд: Danfoss Страницы: 10
SimCom SIM300DZ Manuallines preview
SIM300DZ
Бренд: SimCom Страницы: 13
V2 City7 Instruction Manual preview
City7
Бренд: V2 Страницы: 13
Vag GA INDUSTRIES Figures 251-D Installation, Operation And Maintenance Manual preview
GA INDUSTRIES Figures 251-D
Бренд: Vag Страницы: 6
UCS SYNCHRO QUASAR AC User Manual preview
SYNCHRO QUASAR AC
Бренд: UCS Страницы: 10
Curtis MultiMode 1214-8 Manual preview
MultiMode 1214-8
Бренд: Curtis Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды