background image

4

vacon • 26

Technical data

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

I

th

 = Thermal maximum continuous RMS current. Dimensioning can be done according to this current if the 

process does not require any overloadability or the process does not include any load variation.

I

L

 = Low overloadability current. 10% load variation. 10% exceeding can be continuous.

I

H

 = High overloadability current. 50% load variation. 50% exceeding can be continuous.

All values with cos

ϕ

 = 0.83 and efficiency = 97%.

*) c = power loss into coolant; a = power loss into air; T = total power loss; power losses of input chokes not 
included. All power losses obtained using max. supply voltage, I

th

 and switching frequency of 3.6 kHz and 

Closed Loop control mode. All power losses are worst case losses.

If some other mains voltage is used, apply the formula 

P = 

x Un x In x cos

ϕ

 x eff%

 to calculate the VACON

®

 

NX Liquid-Cooled drive output power.

The enclosure class for all VACON

®

 NX Liquid-Cooled AC drives is IP00.

If the motor is continuously (besides start and stop ramps) run at frequencies below 5 Hz, pay attention to the 
drive dimensioning for low frequencies, i.e. maximum I

H

 = 0.66*I

th

 or choose drive according to I

H

. It is 

recommended to check the rating with your nearest distributor. 

Drive overrating may also be necessary if the process requires high starting torque.

0416_6

416

378

277

250

355

9.1/0.5/9.6

CH72

0460_6

460

418

307

315

400

10.0/0.5/10.5

CH72

0502_6

502

456

335

355

450

11.2/0.6/11.8

CH72

0820_6

820

745

547

600

750

17.3/1.0/18.3

CH74

0920_6

920

836

613

650

850

19.4/1.1/20.5

CH74

1030_6

1030

936

687

750

950

21.6/1.2/22.8

CH74

1180_6

1180

1073

787

800

1100

25.0/1.3/26.3

CH74

1300_6

1300

1182

867

950

1200

27.3/1.5/28.8

CH74

1500_6

1500

1364

1000

1050

1400

32.1/1.7/33.8

CH74

1700_6

1700

1545

1133

1150

1550

36.5/1.9/38.4

Ch74

1850_6

1850

1682

1233

1250

1650

39.0/2.0/41.0

2*CH74

2120_6

2120

1927

1413

1450

1900

44.9/2.4/47.3

2*CH74

2340_6

2340

2127

1560

1600

2100

49.2/2.6/51.8

2*CH74

2700_6

2700

2455

1800

1850

2450

57.7/3.1/60.8

2*CH74

3100_6

3100

2818

2067

2150

2800

65.7/3.4/69.1

2*CH74

Table 10. Internal brake chopper unit (BCU) ratings, braking voltage 840—1100 VDC

Internal brake chopper ratings, braking voltage 840-1100 Vdc

AC drive Type

Loadability

Braking capacity at 840 Vdc

Braking capacity at 1100 Vdc

Chassis

Rated min 

resistance 

[

]

Rated cont. brak-

ing power 

[kW]

BCU rated cont. 

braking current, 

I

br

[A]

Rated cont. brak-

ing power 

[kW]

BCU rated cont. 

braking current, 

I

br

[A]

NX_325 6 

1)

2.8

252

300

432

392

Ch72

NX_385 6 

1)

2.8

252

300

432

392

Ch72

NX_416 6

 1)

2.8

252

300

432

392

Ch72

Table 9. Power ratings of VACON

®

 NX Liquid-Cooled AC drive (12-pulse), 

supply voltage 525—690 VAC

Mains voltage 525-690 VAC, 50/60 Hz, 3~, 12-pulse drives

3

Содержание NX
















































































































































































































































Отзывы: