Vacon NX Скачать руководство пользователя страница 120

Страница: 120 / 239

vacon • 118

Control keypad

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

7.2

Keypad push-buttons

The VACON

alphanumeric control keypad features 9 push-buttons that are used for the control of

the AC drive (and motor), parameter setting and value monitoring.

Figure 61. Keypad push-buttons

7.2.1

Button descriptions

= This button is used to reset active faults (see Chapter 7.3.4).

This button is used to switch between two latest displays. May be useful when
you want to see how the changed new value influences some other value.

The Enter button serves for:
1) confirmation of selections
2) fault history reset (2…3 seconds)

Browser button up
Browse the main menu and the pages of different submenus.
Edit values.

Browser button down
Browse the main menu and the pages of different submenus.
Edit values.

Menu button left
Move backward in menu.
Move cursor left (in parameter menu).
Exit edit mode.
Swap between keypad control and another control as active control place (see
Chapter 7.2.1.1)

Menu button right
Move forward in menu.
Move cursor right (in parameter menu).
Enter edit mode.

3063_00

reset

select

enter





Содержание NX
















































































































































































































































Результаты поиска

Содержание NX

Отзывы:

Похожие инструкции для NX

Бренды по названию

Популярные бренды

Vacon NX, Руководство пользователя

Результаты поиска

Содержание NX

Отзывы:

Похожие инструкции для NX

Бренды по названию

Популярные бренды