manualshive.com logo in svg

Vacon NX, Руководство пользователя

Vacon NX - это мощный преобразователь частоты, предоставляющий быструю помощь с помощью бесплатного руководства. Скачайте руководство с нашего сайта для получения подробной информации о продукте. {Website} - ваш источник полезных ресурсов для вашего оборудования.

Поделиться
Скачать
background image

Fault tracing

vacon • 149

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

9

25

Microprocessor 
watchdog fault

-

faulty operation

-

component failure

Subcodes:
S1 = CPU watchdog timer
S2 = ASIC reset

Reset the fault and restart.
Should the fault re-occur, 
contact your distributor.

26

Startup prevented

Start-up of the drive has been prevented.
Subcodes:
S1 = Prevention of accidental start-up.
S2 = Appears if START command is ON, 
when returning to READY STATE after 
Safe Disable has been active.
S30 = Appears if START command is ON 
after system software has been 
downloaded, after application has been 
downloaded or application has been 
changed.

Cancel prevention of start-up 
if this can be done safely.

29

Thermistor fault

The thermistor input of option board has 
detected increase of the motor tempera-
ture.
Subcodes:
S1 =Thermistor input activated on 
        OPT-AF board
S2 = Special application

Check motor cooling and 
loading.
Check thermistor connection
(If thermistor input of the 
option board is not in use it 
has to be short circuited).

30

Safe Disable 
warning

Safe disable inputs SD1 and SD2 are acti-
vated through the option board OPT-AF.

Contact your distributor.

31

IGBT temperature
(hardware)

IGBT Inverter Bridge overtemperature 
protection has detected too high a short-
term overload current.

Check loading.
Check motor size.

34

CAN bus 
communication

Sent message not acknowledged.

Ensure that there is another 
device on the bus with the 
same configuration.

35

Application

Problem in application software.

Contact your distributor. If 
you are application 
programmer check the 
application program.

36

Control unit

VACON

®

 NXS Control Unit can not con-

trol VACON

®

 NXP Power Unit and vice 

versa.

Change control unit.

37

Device changed
(same type)

Option board or power unit changed.
New device of same type and rating.
Subcodes:
S1 = Control board
S2 = Control unit
S3 = Power board
S4 = Power unit
S5 = Adapter board and slot

Reset. Device is ready for 
use.
Old parameter settings will 
be used.

Table 60. Fault codes

Fault 

code

Fault

Possible cause

Correcting measures

Содержание NX
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX

Rain Bird IQ Installation & User Manual preview
IQ
Бренд: Rain Bird Страницы: 48
Farfisa TD6100 Manual preview
TD6100
Бренд: Farfisa Страницы: 20
Racal Instruments 1266 Manual preview
1266
Бренд: Racal Instruments Страницы: 64
KAESER KOMPRESSOREN SIGMA CONTROL 2 User Manual preview
SIGMA CONTROL 2
Бренд: KAESER KOMPRESSOREN Страницы: 246
X-lander X-cite Manual preview
X-cite
Бренд: X-lander Страницы: 72
X Rocker 2.1 Wireless Manual preview
2.1 Wireless
Бренд: X Rocker Страницы: 38
M-system R1C-GH Instruction Manual preview
R1C-GH
Бренд: M-system Страницы: 13
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Бренд: Eaton Страницы: 38
oventrop 2104203 Operating Instructions Manual preview
2104203
Бренд: oventrop Страницы: 64
WAGO 767-4803/000-800 Manual preview
767-4803/000-800
Бренд: WAGO Страницы: 80
Solaris Vertical Fan Coil Installation And Maintenance Manual preview
Vertical Fan Coil
Бренд: Solaris Страницы: 10
S&C IntelliCap Installation Manual preview
IntelliCap
Бренд: S&C Страницы: 24
PENKO 1020 CAN-RS232-RS422 MFL Manual preview
1020 CAN-RS232-RS422 MFL
Бренд: PENKO Страницы: 29
Bailey Infi 90 IMSPM01 Instruction preview
Infi 90 IMSPM01
Бренд: Bailey Страницы: 52
Lika IF62 User Manual preview
IF62
Бренд: Lika Страницы: 28
Espressif Systems ESP32-DevKitC Getting Started Manual preview
ESP32-DevKitC
Бренд: Espressif Systems Страницы: 11
CAME TOP-43 EE Series Quick Start Manual preview
TOP-43 EE Series
Бренд: CAME Страницы: 2
WattMaster Auto-Zone CV Design, Installation And Operation preview
Auto-Zone CV
Бренд: WattMaster Страницы: 104

Бренды по названию

Популярные бренды

Загрузить еще бренды